Xilinx Design Tools Ise Webpack

This article or section needs language, wiki syntax or style improvements. See Help:Style for reference.

The Xilinx ISE WebPACK is a complete FPGA/CPLD programmable logic design suite providing:

Specification of programmable logic via schematic capture or Verilog/VHDL
Synthesis and Place & Route of specified logic for various Xilinx FPGAs and CPLDs
Functional (Behavioral) and Timing (post-Place & Route) simulation
Download of configuration data into target device via communications cable

The development of the ISE WebPACK has been stopped in favor of the Vivado Suite, but it is still useful to develop for older devices not supported by the new suite.

While Arch Linux is not one of the officially supported distributions, many features are known to work on Arch Linux.

Prerequisites

Download ISE WebPACK

The Xilinx ISE WebPACK is a freeware software released under a proprietary license which does not allow redistribution. To obtain the install data visit the official download page.

Dependencies

Several tools included in the ISE Webpack (and the installer itself) depends on ncurses5-compat-libs ^AUR. Additionally^{[dead link 2021-11-19 ⓘ]} other tools (e.g. the FPGA editor) requires libstdc++5 openmotif xorg-fonts-75dpi xorg-fonts-100dpi.

If you plan to develop software for an embedded ARM core (e.g. for Xilinx Zynq SoC devices), you will want to install the GCC cross-compiler bundled included with the Xilinx Embedded Development Kit (EDK). This compiler requires the lib32-glibc package from the multilib repository and lib32-ncurses5-compat-libs ^AUR from the AUR.

Default Shell

During the installation, the Mentor CodeSourcery toolchains for embedded processors can be installed along with the Xilinx tools. This installation silently fails when the default shell is set to dash. Make sure /usr/bin/sh points to /usr/bin/bash.

This can be checked by running this command:

$ ls -l /usr/bin/sh

If the output looks like this:

          lrwxrwxrwx 1 root root 15 13 Mar 06:47 /usr/bin/sh -> bash

then /usr/bin/sh already points to /usr/bin/bash. (the default in Arch Linux).

If not, link /usr/bin/sh to bash:

# ln -sfT bash /usr/bin/sh

Installation

Install from AUR

Install the package xilinx-ise ^AUR, you will have to place the tarball with the installation data in the same folder of the PKGBUILD before starting the building process.

Manual installation

Note: The installation is last known to work with Xilinx ISE 14.7, requiring the dynamic library fix described below.

Extract the tarball containing the installation data:

$ tar -xvf Xilinx_ISE_DS_Lin_14.7_1015_1.tar

The ISE design tools installer is a Qt application. If you are running the KDE desktop environment, the installer may try to load the "Oxygen" widget theme, which will fail due to the older Qt framework bundled with the Xilinx ISE design tools. You need to remove the QT_PLUGIN_PATH environment variable before executing the installer:

$ unset QT_PLUGIN_PATH

Then, install the ISE Design Tools:

$ cd Xilinx_ISE_DS_Lin_14.7_1015_1 $ ./xsetup

Follow the instructions to install the ISE. By default, the whole application is installed to /opt/Xilinx/, so make sure the user running the installer has permissions to write to this directory.

During installation, uncheck the "Install Cable Drivers" option. Leaving it checked will cause errors during the installation.

Launching the ISE design tools

The ISE design tools include a shell script that modifies the environment variables (mostly PATH and LD_LIBRARY_PATH). This script must be sourced before starting the ISE tools:

$ source /opt/Xilinx/14.7/ISE_DS/settings64.sh

or, for a 32-bit installation:

$ source /opt/Xilinx/14.7/ISE_DS/settings32.sh

Then, the ISE design tools will be found in your PATH and can be started by typing their name in the terminal (e.g. ise, planAhead, xsdk, ...)

Launching via desktop icons

You can also create a desktop entry at /usr/share/applications/

/usr/share/applications/ise.desktop

#!/usr/bin/env xdg-open [Desktop Entry] Version=1.0 Type=Application Name=Xilinx ISE Exec=sh -c "unset LANG && unset QT_PLUGIN_PATH && source /opt/Xilinx/14.7/ISE_DS/settings64.sh && ise" Icon=/opt/Xilinx/14.7/ISE_DS/ISE/data/images/pn-ise.png Categories=Development; Comment=Xilinx ISE StartupWMClass=_pn

After that you can copy this file to the ~/Desktop folder and launch ISE tools from the desktop.

License Installation

After requesting a WebPACK license from Xilinx using their Licensing Site, you will be e-mailed a license file. This file can be imported with the Xilinx License Manager (run xlcm -manage from the terminal).

Another way to import the license is to simply copy it to the ~/.Xilinx or /opt/Xilinx/14.7/ISE_DS/ISE/coregen/core_licenses directory.

Node-Locked Licenses

Arch Linux by default uses systemd's Predictable Network Interface Names^{[broken link: invalid section]}. This means that your system will most likely not have its network interfaces named "eth0", "eth1" and so forth.

However, the Xilinx License Manager looks for these names to find out the system's MAC addresses, which are used for node-locked licenses. If you want to use node-locked licenses, you will have to manually assign to your interface a name in the format expected by the License Manager. The change device name^{[broken link: invalid section]} article subsection explain how to write an udev rule to do so. If your machine does not have a wired ethernet adapter, then it is possible to use the systemd and the dummy kernel module to create a virtual ethernet adapter with the proper MAC address. To do this, create

/etc/systemd/network/25-dummy.netdev

[Match]  [NetDev] Name=eth0 Kind=dummy MACAddress=00:11:22:33:44:55:66

and restart systemd-networkd.

Post-Installation Fixes and Tweaks

After installation, a few manual fixes are required to work around problems caused by running the Xilinx tools on a Linux distribution that is not officially supported by Xilinx. Some of these fixes are taken from this forum post.

Dynamic Library Fix (libstdc++.so)

Note: This workaround is already applied in the AUR package

The ISE tools supply an outdated version of the libstdc++.so library, which may cause segfaults when using the Xilinx Microprocessor Debugger and prevents the usage of the oxygen-gtk theme. This outdated version is located in two directories within the installation tree: /opt/Xilinx/14.7/ISE_DS/ISE/lib/lin64/ and /opt/Xilinx/14.7/ISE_DS/common/lib/lin64. To use Arch's newer version of libstdc++, rename or delete the original files and replace them with symlinks:

$ cd /opt/Xilinx/14.7/ISE_DS/ISE/lib/lin64/ $ mv libstdc++.so libstdc++.so.bak $ mv libstdc++.so.6 libstdc++.so.6.bak $ mv libstdc++.so.6.0.8 libstdc++.so.6.0.8.bak $ ln -s /usr/lib/libstdc++.so $ ln -s libstdc++.so libstdc++.so.6 $ ln -s libstdc++.so libstdc++.so.6.0.8

Then, repeat this process in the /opt/Xilinx/14.7/ISE_DS/common/lib/lin64 directory.

Digilent USB-JTAG Drivers

To use Digilent Adept USB-JTAG adapters (e.g. the onboard JTAG adapter on the ZedBoard) from within the Xilinx design tools, you need to install the Digilent Adept Runtime and Plugin.

Make sure you have installed fxload ^AUR from the Arch User Repository .

To install the Digilent Adept Runtime, it is recommended to install digilent.adept.runtime ^AUR from the Arch User Repository.

In addition, installing digilent.adept.utilities ^AUR may do good to configuring your board.

To install the Digilent plugin, you have to copy two files to the ISE plugin directory. Run the following commands as root:

$ mkdir -p /opt/Xilinx/14.7/ISE_DS/ISE/lib/lin64/plugins/Digilent/libCseDigilent $ cd /opt/Xilinx/14.7/ISE_DS/ISE/bin/lin64/digilent/libCseDigilent_2.4.4-x86_64/lin64/14.1/libCseDigilent $ cp libCseDigilent.{so,xml} /opt/Xilinx/14.7/ISE_DS/ISE/lib/lin64/plugins/Digilent/libCseDigilent $ chmod -x /opt/Xilinx/14.7/ISE_DS/ISE/lib/lin64/plugins/Digilent/libCseDigilent/libCseDigilent.xml

Finally, add every user that should have access to the Digilent USB-JTAG adapter to the "uucp" group.

To grant access to the usb driver for normal users you may have to add the USB Vendor/Product IDs of your JTAG adapter which can be found with

$ lsusb | grep Xilinx

to the udev rules in /etc/udev/rules.d/20-digilent.rules:

SUBSYSTEM=="usb", ATTRS{idVendor}=="xxxx", ATTRS{idProduct}=="xxxx", GROUP="users", MODE="666"

If it still does not work, you can make further reading in Xilinx_JTAG_Linux. The magic git repo there may be help.

Xilinx Platform Cable USB-JTAG Drivers

Make sure you have installed fxload ^AUR or fxload-libusb ^AUR from the Arch User Repository . We need to build driver from source (git and some make stuff need to be installed, make will say what programs or libraries are missed):

$ cd /opt/Xilinx # git clone git://git.zerfleddert.de/usb-driver $ cd usb-driver/ $ make

If you using 32-bit version of ISE on 64-bit system, pass "lib32" to make:

$ make lib32

And install driver (replace 14.7 to your version):

$ ./setup_pcusb /opt/Xilinx/14.7/ISE_DS/ISE

Or in older versions:

$ ./setup_pcusb /opt/Xilinx/10.x/ISE

For the new fxload version: fxload-libusb ^AUR, the file /etc/udev/rules.d/xusbdfwu.rules needs to be changed to:

$ /etc/udev/rules.d/xusbdfwu.rules

ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="0008", MODE="666" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="0007", RUN+="/usr/bin/fxload-libusb -t fx2 -I /usr/share/xusbdfwu.hex -d 03fd:0007" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="0009", RUN+="/usr/bin/fxload-libusb -t fx2 -I /usr/share/xusb_xup.hex -d 03fd:0009" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="000d", RUN+="/usr/bin/fxload-libusb -t fx2 -I /usr/share/xusb_emb.hex -d 03fd:000d" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="000f", RUN+="/usr/bin/fxload-libusb -t fx2 -I /usr/share/xusb_xlp.hex -d 03fd:000f" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="0013", RUN+="/usr/bin/fxload-libusb -t fx2 -I /usr/share/xusb_xp2.hex -d 03fd:0013" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="03fd", ATTRS{idProduct}=="0015", RUN+="/usr/bin/fxload-libusb -t fx2 -I /usr/share/xusb_xse.hex -d 03fd:0015"

When performing this command, the udev rules file will be created. You can reload udev rules to apply changes immediately:

# udevadm control --reload-rules

If driver installed correctly and udev rule works, STATUS led should turn on (green or red depending on voltage presence on VREF PIN)

Note: This step is only required for versions of Xilinx ISE older than 11.1: In older versions, iMPACT does not correctly load the right drivers (it still tries to use windrvr6 drivers). To fix this, the environment variable LD_PRELOAD must be set so that the libusb drivers are loaded into iMPACT without recompiling it.

$ export LD_PRELOAD=/opt/Xilinx/usb-driver/libusb-driver.so

Locale Issues

PlanAhead does not like locales using other literals than '.' as the decimal point (e.g. German, which uses ','). Run the following command before launching PlanAhead:

$ unset LANG

Segmentation Fault on PlanAhead

When launching PlanAhead to generate a .ucf file, a segmentation fault may occur. The issue seems unrelated to the previous topic. The ISE console will show

"/opt/Xilinx/14.7/ISE_DS/PlanAhead/bin/rdiArgs.sh: line 64: 14275 Segmentation fault      $RDI_PROG $*"

The problem seems to come from the bundled JRE as described here^{[dead link 2021-11-19 ⓘ]}. To fix the issue, symlink the OpenJDK libjvm.so into the Xilinx's installation directory.

# cd /opt/Xilinx/14.7/ISE_DS/PlanAhead/tps/lnx64/jre/lib/amd64/server # mv libjvm.so{,-orig} # ln -s /usr/lib/jvm/java-7-openjdk/jre/lib/amd64/server/libjvm.so

GNU make

XSDK looks for the gmake executable, which is not present in Arch Linux by default. Create a symlink somewhere in your path, e.g.

$ ln -s /usr/bin/make /home/<user>/bin/gmake

Make sure this directory is in your PATH variable.

Running Xilinx tools from within KDE

KDE by default defines the QT_PLUGIN_PATH shell variable. Some of the Xilinx ISE tools (ISE, Impact, XPS) are Qt applications, which means that they will search for Qt plugins in the locations defined by this shell variable.

Because the Xilinx tools are compiled against and ship with an older version of the Qt framework which cannot use these plugins, they will crash when launched with this environment variable present.

To fix this issue, run the following command before launching the tools:

$ unset QT_PLUGIN_PATH

CORE Generator fails to generate core

In some cases, the CORE Generator will fails to generate a core and output something like this to its console:

ERROR:sim - Unable to evaluate Tcl file:    /opt/Xilinx/14.7/ISE_DS/ISE/coregen/ip/xilinx/primary/com/xilinx/ip/clk_wiz_v3_6/generate/run_legacy_tcl_flow.tcl ERROR:sim - Failed executing Tcl generator.

Solution #1

If that happens, make sure you do not have _JAVA_OPTIONS set in your environment. If you normally run coregen with

$ source /opt/Xilinx/14.7/ISE_DS/settings64.sh && coregen

you need to prepend that with an "unset _JAVA_OPTIONS":

$ unset _JAVA_OPTIONS && source /opt/Xilinx/14.7/ISE_DS/settings64.sh && coregen

Solution #2

Solution #1 no longer works due to: coregen's bundled java fails to start. Workaround force using ISE bundled java6 instead of java5.

Backup old version

$ mv /opt/Xilinx/14.7/ISE_DS/ISE/java/lin64/jre/bin/java /opt/Xilinx/14.7/ISE_DS/ISE/java/lin64/jre/bin/java.old

Add symbolic link to java6

$ ln -s /opt/Xilinx/14.7/ISE_DS/ISE/java6/lin64/jre/bin/java /opt/Xilinx/14.7/ISE_DS/ISE/java/lin64/jre/bin/java

Solution #3

If the previous methods fail, try to run the 32-bit version of coregen:

$ unset _JAVA_OPTIONS && source /opt/Xilinx/14.7/ISE_DS/settings32.sh && coregen